Of CSY2011-X for the upgraded version of the TH2010-X, TH2010-X as the light bar or test CSY2011-X project outline lighting on a dedicated, available in a variety of buildings, bridges, buildings lighting engineering,stable, simple wiring, and easy to operate, use the shortcut.

Its contours better than the SD card controller effect is more beautiful, natural, smooth, because all the effect of the program algorithm without dropping frames recorded the effect of non-SD card controller, from the price, quality, effectiveness, in terms of may be the best choice of the contour lighting project.

   4 button operation, 4 digital tube display, easy to operate, intuitive display.



     8-port, per port comes with two kinds of signal output TTL signals and 485 differential signal (long-distance transmission), only 4-port control wire IC.


     Built-in 114 kinds of outline effect, rich, beautiful, natural, smooth, non-SD card controller than without their own recording of the peace of mind and convenient.


     Any combination of the effects loop (which can edit the playback menu, for example, playback, playback, playback of 100 and so on, can be recorded up to 32 effect combinations of loop), the effect of application of heart and wish.


     AC AC synchronous (each controller parameter adjust, power-on at the same time, you can sync), application is quick and easy, so that the entire project control system to a more simplistic.


      Connection synchronization (parameters need to set, do not power on, set a good master, the master on the operating points change in control followed), convenient connection, the synchronization is more stable.


      Can be controlled on all single line, two-lane Lighting IC (orders must be marked with the IC model, the instructions for the singlet series).

     RXA: simultaneous reception line.

       RXB: simultaneous reception of the B line.

       The TXA: Send A line synchronization.

       TXB: synchronized to send the B line.

       DATx +: data output of the DAT, but also the differential data signal output line (A) using 485 then 485 receiver board.

       GND: Signal ground.

       DATx-: differential signal data output line B (485 by 485 B receiver board).

       CLKx +: clock output CLK is also a differential clock signal output line (using 485 then 485 receiving plate A), a control wire IC. If this interface is equivalent to DATx + control singlet IC.

       GND: Signal ground.

       CLKx-: clock output of the differential signal line B (using 485 by 485 receiver board B), a control wire IC. If this interface is equivalent to DATx-control single line IC.

Data output port comes with two kinds of signals, TTL signals and 485 differential signal, then the method is as follows:

       TTL signals: data on the light bar DIN then DATx +, GND GND clock CLK to pick CLKx + to (control lane IC to pick up the clock line, the control singlet IC interface is also a data port DATx +).        

       Differential signal: 485 Data differential receiver board B access DATx-, A, to pick DATx + B access CLKx-485 clock differential receiver board A, to pick CLKx +. (Note: The use of the differential signal must be before the light bar plus a 485 differential receiver converter board must be added to the control wire IC 2, the clock and data lines, it is recommended to use this controller supporting 485 differential receive converter board, Model: TH2010-485MD).

Connection synchronized connection: a controller on the TXA, TXB, respectively, to take over a controller RXA, RXB, one a cascade down, up to cascade 64. The distance between each controller up to 200 meters. The synchronous master menu is set to "F-Sr points to control the synchronization menu is set to the F-Ct", connection diagram is as follows: 

    (1) On / Off: Power on / off

    (2), -: mode - / Speed ​​-

    (3), +: mode + / Speed ​​+

    (4), the Mode / Speed​​: Mode conditioning / speed adjustment function switch

    H-XX: Repeat Playback (playback) fixed effects loop in Article XX.

    A-XX: All loop (the effect of 01-A7 loop automatically A8-B3, the effect of static monochrome, does not participate in play), when the switch to the H-00 channels, one second after the whole loop, the digital control   automatically appear as the A-XX, where XX is the effect of ID number currently playing.

    C-XX: any combination of the effects loop, when the switch to the H-b4 channel one seconds later, the effect of any combination of loop, digital tube automatically appear as the C-XX, where XX is currently playing effects ID number.

    E-XX: represents the current playback speed, XX is the speed rating, 10 grades 01-10, the larger the number the faster.

Eight.Case

Nine Model Description: